| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
usb: gadget: uvc: clamp SEND_RESPONSE length to the response buffer
uvc_send_response() builds the UVC control response from a user-supplied
struct uvc_request_data:
req->length = min_t(unsigned int, uvc->event_length, data->length);
...
memcpy(req->buf, data->data, req->length);
req->length is clamped to uvc->event_length, which is taken from the
host control request wLength (up to UVC_MAX_REQUEST_SIZE, 64), and to
data->length, which comes from the UVCIOC_SEND_RESPONSE ioctl and is
only checked for being negative. The source buffer data->data is only
60 bytes, so a response with uvc->event_length and data->length both
greater than 60 makes memcpy() read past the end of data->data.
Clamp req->length to sizeof(data->data) as well. |
| In the Linux kernel, the following vulnerability has been resolved:
dpaa2-eth: put MAC endpoint device on disconnect
fsl_mc_get_endpoint() returns the MAC endpoint device with a reference
taken through device_find_child(). The Ethernet connect path stores that
device in mac->mc_dev and keeps it for the lifetime of the connected MAC
object.
However, the disconnect path only disconnects and closes the MAC before
freeing the dpaa2_mac object. It does not drop the endpoint device
reference stored in mac->mc_dev, so every successful connect leaks that
device reference when the MAC is later disconnected.
Drop the endpoint device reference after closing the MAC and before
freeing the dpaa2_mac object. |
| In the Linux kernel, the following vulnerability has been resolved:
bnxt_en: Handle partially initialized auxiliary devices
bnxt_aux_devices_init() calls auxiliary_device_init() before all fields
used by bnxt_aux_dev_release() are initialized. After
auxiliary_device_init() succeeds, later errors must unwind with
auxiliary_device_uninit(), which invokes the release callback.
The release callback assumes that aux_priv->id, aux_priv->edev,
edev->net and edev->ulp_tbl are all populated. If allocation fails
after auxiliary_device_init(), the release path can otherwise dereference
or clear partially initialized state.
Allocate and attach the bnxt_en_dev and ULP table before calling
auxiliary_device_init(), so the release callback only sees a fully
initialized auxiliary private object. If auxiliary_device_init() itself
fails, free those allocations directly because device_initialize() has not
run and the release callback will not be invoked.
This issue was found by a static analysis checker and confirmed by manual
source review. |
| In the Linux kernel, the following vulnerability has been resolved:
dpll: fix NULL pointer dereference in dpll_msg_add_pin_ref_sync()
When a dpll_pin is shared across multiple dpll_device instances and
those devices are being unregistered (e.g. during driver module removal),
a NULL pointer dereference can occur in dpll_msg_add_pin_ref_sync().
This happens under the following conditions:
- A pin is registered with two or more dpll devices (dpll_A, dpll_B)
- The pin has ref_sync pairs with other pins
- During unregistration of dpll_A's pins, a ref_sync partner pin is
unregistered first, removing it from dpll_A->pin_refs
- But since the partner pin is still registered with dpll_B, its
dpll_refs is not empty, so dpll_pin_ref_sync_pair_del() does NOT
run and the partner stays in the pin's ref_sync_pins xarray
- When the pin itself is then unregistered from dpll_A, the delete
notification calls dpll_msg_add_pin_ref_sync() which finds the
partner in ref_sync_pins, passes dpll_pin_available() (partner is
still registered with dpll_B), but dpll_pin_on_dpll_priv(dpll_A,
partner) returns NULL because partner was already removed from
dpll_A->pin_refs
- The NULL priv pointer is passed to the driver's ref_sync_get
callback, which dereferences it
BUG: kernel NULL pointer dereference, address: 0000000000000034
Oops: Oops: 0000 [#1] SMP NOPTI
RIP: 0010:zl3073x_dpll_input_pin_ref_sync_get+0x73/0x80 [zl3073x]
Call Trace:
dpll_msg_add_pin_ref_sync+0xb8/0x200
dpll_cmd_pin_get_one+0x3b6/0x4b0
dpll_pin_event_send+0x72/0x140
__dpll_pin_unregister+0x5a/0x2b0
dpll_pin_unregister+0x49/0x70
Fix this by skipping ref_sync pins whose priv pointer cannot be resolved
for the current dpll device. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: mt76: mt7915: guard HE capability lookups
mt7915_mcu_bss_he_tlv() and mt7915_mcu_sta_bfer_tlv() both run after
checking HE support, then dereference the HE PHY capability returned by
mt76_connac_get_he_phy_cap(). That helper can return NULL when no
capability entry matches the vif type.
Fetch the capability before appending the TLV and skip the HE-specific
setup when no matching capability is available. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: ath11k: fix NULL pointer dereference in ath11k_hal_srng_access_begin
In ATH11K_QMI_EVENT_FW_READY, ATH11K_FLAG_REGISTERED is set
unconditionally even when ath11k_core_qmi_firmware_ready() fails.
This leaves the driver in an inconsistent state where
initialization is considered complete although the firmware ready
handling did not finish successfully. During the subsequent SSR,
the driver enters the restart path based on this incorrect state
and dereferences uninitialized srng members, resulting in a NULL
pointer dereference.
Call trace:
ath11k_hal_srng_access_begin+0xc/0x60 [ath11k] (P)
ath11k_ce_cleanup_pipes+0x17c/0x180 [ath11k]
ath11k_core_restart+0x40/0x168 [ath11k]
Fix this by:
- skipping firmware_ready if ATH11K_FLAG_REGISTERED is already set
- setting ATH11K_FLAG_REGISTERED only when firmware_ready succeeds
- setting ATH11K_FLAG_QMI_FAIL and aborting the FW_READY handling
on error
Tested-on: WCN6750 hw1.0 AHB WLAN.MSL.2.0.c2-00204-QCAMSLSWPLZ-1 |
| In the Linux kernel, the following vulnerability has been resolved:
bpf: Reject redirect helpers without a bpf_net_context
The bpf_redirect*() helpers and skb_do_redirect() obtain the per-task
bpf_redirect_info via bpf_net_ctx_get_ri(), which dereferences the
current->bpf_net_context unconditionally. That context is established
on the paths that run tc BPF such as sch_handle_{ingress,egress}(),
*except* for the case where {cls,act}_bpf was attached to a proper
qdisc. A program running from there reaches the NULL deref in two ways:
* It calls bpf_redirect() directly, which dereferences the context at
the top of the helper:
tc qdisc add dev eth0 root handle 1: red limit 1MB min 10KB max 20KB \
avpkt 1000 burst 100 qevent early_drop block 10
tc filter add block 10 pref 1 bpf obj redirect.o
* It simply returns TC_ACT_REDIRECT without helper call: tcf_qevent_handle()
then dispatches to skb_do_redirect(), which dereferences the context
Rather than extending bpf_net_context management into the qdisc path,
make the redirect helpers refuse to operate when no context exists, and
have tcf_qevent_handle() drop a TC_ACT_REDIRECT verdict instead of
calling skb_do_redirect(). Previous behaviour was a crash, so nothing
regresses by not supporting it. |
| In the Linux kernel, the following vulnerability has been resolved:
Bluetooth: btusb: validate Realtek vendor event length
btusb_recv_event_realtek() reads the event code at data[0] and the Realtek
subevent code at data[2] before deciding whether to consume a vendor event
as a coredump.
For example, the two-byte event ff 00 contains a complete vendor-event
header declaring zero parameters. The old classifier still reads a
nonexistent third byte and can misclassify the event as a coredump if the
adjacent byte is 0x34.
Require the HCI event header and first parameter to be present before
inspecting the Realtek subevent code. Short events continue through the
normal HCI receive path, which owns their protocol validation. |
| In the Linux kernel, the following vulnerability has been resolved:
arm_mpam: guard MBWU state before adding it to garbage
__destroy_component_cfg() adds each RIS mbwu_state object to the MPAM
garbage list when destroying component configuration.
However, mbwu_state is allocated per RIS and only for RISes with MBWU
monitors. A component can therefore have comp->cfg allocated while some
RISes still have ris->mbwu_state set to NULL.
Passing a NULL mbwu_state to add_to_garbage() dereferences the NULL
pointer inside the macro.
Skip RISes that do not have an mbwu_state object before adding them to
the garbage list. |
| In the Linux kernel, the following vulnerability has been resolved:
bonding: fix devconf_all NULL dereference when IPv6 is disabled
When booting with the 'ipv6.disable=1' parameter, the devconf_all is
never initialized because inet6_init() exits before addrconf_init() is
called which initializes it. bond_send_validate(), however, will still
call bond_ns_send_all() even ipv6 is indeed disabled. It will lead to
NULL derefence of net->ipv6.devconf_all in ip6_pol_route().
BUG: kernel NULL pointer dereference, address: 000000000000000c
[...]
Workqueue: bond0 bond_arp_monitor [bonding]
RIP: 0010:ip6_pol_route+0x69/0x480
[...]
Call Trace:
<TASK>
? srso_return_thunk+0x5/0x5f
? __pfx_ip6_pol_route_output+0x10/0x10
fib6_rule_lookup+0xfe/0x260
? wakeup_preempt+0x8a/0x90
? srso_return_thunk+0x5/0x5f
? srso_return_thunk+0x5/0x5f
? sched_balance_rq+0x369/0x810
ip6_route_output_flags+0xd7/0x170
bond_ns_send_all+0xde/0x280 [bonding]
bond_ab_arp_probe+0x296/0x320 [bonding]
? srso_return_thunk+0x5/0x5f
bond_activebackup_arp_mon+0xb4/0x2c0 [bonding]
process_one_work+0x196/0x370
worker_thread+0x1af/0x320
? srso_return_thunk+0x5/0x5f
? __pfx_worker_thread+0x10/0x10
kthread+0xe3/0x120
? __pfx_kthread+0x10/0x10
ret_from_fork+0x199/0x260
? __pfx_kthread+0x10/0x10
ret_from_fork_asm+0x1a/0x30
</TASK>
Fix this by adding ipv6_mod_enabled() condition check in the caller. |
| In the Linux kernel, the following vulnerability has been resolved:
wan: wanxl: Only reset hardware after BAR mapping
wanxl_pci_init_one() stores the freshly allocated card in driver data
before the PLX BAR is mapped. Several early probe failures then unwind
through wanxl_pci_remove_one(), including failure to allocate the coherent
status area or to restore the DMA mask.
wanxl_pci_remove_one() unconditionally calls wanxl_reset(), and
wanxl_reset() dereferences card->plx. On those early failures card->plx
is still NULL, so the error path can dereference a NULL MMIO pointer.
Only issue the hardware reset once the BAR mapping exists. The remaining
cleanup in wanxl_pci_remove_one() already checks whether later resources
were allocated.
This issue was found by a static analysis checker and confirmed by
manual source review. |
| In the Linux kernel, the following vulnerability has been resolved:
nfp: Check resource mutex allocation
nfp_cpp_resource_find() allocates a CPP mutex handle for the matching
resource-table entry and then reports success. nfp_resource_try_acquire()
immediately passes that handle to nfp_cpp_mutex_trylock().
However, nfp_cpp_mutex_alloc() returns NULL on failure. If that happens
for a matching table entry, the resource lookup still returns success and
the following trylock dereferences a NULL mutex pointer while opening the
resource.
nfp_resource_acquire() already treats failure to allocate the table mutex
as -ENOMEM. Do the same for the resource mutex and fail the lookup before
publishing the rest of the resource handle.
This issue was found by a static analysis checker and confirmed by
manual source review. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: mt76: mt7996: check pointer returned by mt76_connac_get_he_phy_cap()
mt76_connac_get_he_phy_cap routine can theoretically return NULL so
check cap pointer before dereferencing it. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: mt76: mt7925: guard link STA in decap offload
mt7925_sta_set_decap_offload() iterates over the vif valid_links mask
when updating decap offload state for an MLO station. The station may not
have a link STA for every valid link of the vif, so mt792x_sta_to_link()
can return NULL for a link that belongs to the vif but not to the station.
The function currently dereferences mlink before checking whether the
link WCID is ready. If mlink is NULL, setting or clearing
MT_WCID_FLAG_HDR_TRANS dereferences a NULL pointer.
Skip links without a station link before touching mlink->wcid. |
| In the Linux kernel, the following vulnerability has been resolved:
rds: Fix inet6_addr_lst NULL dereference when IPv6 is disabled
When booting with the 'ipv6.disable=1' parameter, inet6_addr_lst
is never initialized because inet6_init() exits before addrconf_init()
is called to initialize it. An attempt to bind an RDS socket to
an ipv6 address results in a crash in __ipv6_chk_addr_and_flags()
KASAN: null-ptr-deref in range [0x0000000000000008-0x000000000000000f]
RIP: 0010:__ipv6_chk_addr_and_flags+0x1df/0x7e0
Call Trace:
<TASK>
ipv6_chk_addr+0x3b/0x50
rds_tcp_laddr_check+0x155/0x3b0 [rds_tcp]
rds_trans_get_preferred+0x15d/0x2d0 [rds]
? trace_hardirqs_on+0x2d/0x110
rds_bind+0x1433/0x1d60 [rds]
? rds_remove_bound+0xd50/0xd50 [rds]
? aa_af_perm+0x250/0x250
? __might_fault+0xde/0x190
? __sys_bind+0x1dc/0x210
__sys_bind+0x1dc/0x210
? __ia32_sys_socketpair+0x100/0x100
? restore_fpregs_from_fpstate+0x53/0x100
__x64_sys_bind+0x73/0xb0
? syscall_enter_from_user_mode+0x1c/0x50
do_syscall_64+0x34/0x80
entry_SYSCALL_64_after_hwframe+0x6e/0xd8
RIP: 0033:0x7f47f8269ea9
</TASK>
The following code reproduces the issue:
struct sockaddr_in6 addr;
s = socket(PF_RDS, SOCK_SEQPACKET, 0);
memset(&addr, 0, sizeof(addr));
inet_pton(AF_INET6, ADDRESS, &addr.sin6_addr);
addr.sin6_family = AF_INET6;
addr.sin6_port = htons(PORT);
bind(s, &addr, sizeof(addr));
Found by InfoTeCS on behalf of Linux Verification Center
(linuxtesting.org) with Syzkaller. |
| In the Linux kernel, the following vulnerability has been resolved:
drm/imagination: fix error checking of pvr_vm_context_lookup()
Since pvr_vm_context_lookup() returns either NULL or a pointer, then stop
using IS_ERR() for checking the return value.
Using IS_ERR() leads to the kernel oops reported below. It can be
reproduced by passing an invalid VM context handle from userspace to the
DRM_IOCTL_PVR_CREATE_CONTEXT ioctl.
[ 92.733119] Unable to handle kernel NULL pointer dereference at virtual address 0000000000000148
[ 92.742042] Mem abort info:
[ 92.744890] ESR = 0x0000000096000004
[ 92.748686] EC = 0x25: DABT (current EL), IL = 32 bits
[ 92.754020] SET = 0, FnV = 0
[ 92.757154] EA = 0, S1PTW = 0
[ 92.760337] FSC = 0x04: level 0 translation fault
[ 92.765243] Data abort info:
[ 92.768129] ISV = 0, ISS = 0x00000004, ISS2 = 0x00000000
[ 92.773626] CM = 0, WnR = 0, TnD = 0, TagAccess = 0
[ 92.778763] GCS = 0, Overlay = 0, DirtyBit = 0, Xs = 0
[ 92.784098] user pgtable: 4k pages, 48-bit VAs, pgdp=000000088ed23000
[ 92.790550] [0000000000000148] pgd=0000000000000000, p4d=0000000000000000
[ 92.797381] Internal error: Oops: 0000000096000004 [#1] SMP
[ 92.803027] Modules linked in: powervr
[ 92.852533] CPU: 0 UID: 0 PID: 409 Comm: triangle Not tainted 7.1.0-rc5-g98b46e693b91 #1 PREEMPT
[ 92.861385] Hardware name: Texas Instruments AM68 SK (DT)
[ 92.866766] pstate: 60000005 (nZCv daif -PAN -UAO -TCO -DIT -SSBS BTYPE=--)
[ 92.873709] pc : pvr_vm_get_fw_mem_context+0x0/0xc [powervr]
[ 92.879376] lr : pvr_queue_create+0x26c/0x440 [powervr]
[ 92.884595] sp : ffff8000837fbb00
[ 92.887895] x29: ffff8000837fbb60 x28: 0000000000000000 x27: ffff8000837fbce8
[ 92.895015] x26: ffff000807f61a40 x25: ffff000807f61a00 x24: ffff000807f64400
[ 92.902135] x23: ffff00080a5ab000 x22: ffff800079b24730 x21: ffff000807f61800
[ 92.909254] x20: ffff00080999e680 x19: 0000000000000000 x18: 0000000000000000
[ 92.916373] x17: 0000000000000000 x16: 0000000000000000 x15: 0000000000000001
[ 92.923492] x14: 0000000000000000 x13: 0000000000000002 x12: ffff80008145b298
[ 92.930611] x11: ffff8000844e5000 x10: ffff80008165a130 x9 : 0000000000000100
[ 92.937730] x8 : 0000000000000001 x7 : ffff0008076b27e0 x6 : ffff00080ec43b7c
[ 92.944850] x5 : ffff00080ec43b78 x4 : 0000000000000000 x3 : ffff00080999e680
[ 92.951968] x2 : 0000000000000000 x1 : 0000000000000000 x0 : 0000000000000000
[ 92.959088] Call trace:
[ 92.961521] pvr_vm_get_fw_mem_context+0x0/0xc [powervr] (P)
[ 92.967173] pvr_context_create+0x190/0x410 [powervr]
[ 92.972218] pvr_ioctl_create_context+0x44/0x8c [powervr]
[ 92.977608] drm_ioctl_kernel+0xbc/0x124 [drm]
[ 92.982127] drm_ioctl+0x1f8/0x4dc [drm]
[ 92.986098] __arm64_sys_ioctl+0xac/0x104
[ 92.990102] invoke_syscall+0x54/0x10c
[ 92.993842] el0_svc_common.constprop.0+0x40/0xe0
[ 92.998532] do_el0_svc+0x1c/0x28
[ 93.001835] el0_svc+0x38/0x11c
[ 93.004969] el0t_64_sync_handler+0xa0/0xe4
[ 93.009139] el0t_64_sync+0x198/0x19c
[ 93.012792] Code: aa1703e0 d2800014 95cb0ba4 17ffffe8 (f940a400)
[ 93.018869] ---[ end trace 0000000000000000 ]--- |
| In the Linux kernel, the following vulnerability has been resolved:
drm/amdgpu: check amdgpu_vm_bo_find() result in GET_MAPPING_INFO
The AMDGPU_GEM_OP_GET_MAPPING_INFO path of amdgpu_gem_op_ioctl() looks
up the bo_va for the buffer object in the caller's VM via
amdgpu_vm_bo_find(), but uses the returned pointer without checking it.
amdgpu_vm_bo_find() returns NULL when the BO has no bo_va in that VM,
which is the normal case for a BO that has never been mapped. The result
is fed straight into amdgpu_vm_bo_va_for_each_valid_mapping(), which
expands to list_for_each_entry(mapping, &(bo_va)->valids, list) and
dereferences bo_va, causing a NULL pointer dereference.
This is reachable by any process able to issue the ioctl (render group)
simply by requesting mapping info for an unmapped BO.
Return -ENOENT when no bo_va is found, jumping to out_exec so the
drm_exec context and GEM object reference are released.
(cherry picked from commit 528b19377affc1cc7362a70a254c1dda793595f9) |
| In the Linux kernel, the following vulnerability has been resolved:
tipc: fix integer overflow in tipc_recvmsg() and tipc_recvstream()
In tipc_recvmsg(), the copy length is computed as:
copy = min_t(int, dlen - offset, buflen);
buflen is size_t but min_t(int, ...) casts it to int. When buflen
exceeds INT_MAX (e.g. 0xFFFFFFFF via io_uring provided buffers), it
wraps negative, wins the comparison, and the negative copy length
propagates to simple_copy_to_iter() where int-to-size_t promotion
makes it SIZE_MAX, triggering a WARN_ON. tipc_recvstream() has the
same pattern.
Kernel panic - not syncing: kernel: panic_on_warn set ...
RIP: 0010:simple_copy_to_iter+0x9e/0xd0 (net/core/datagram.c:521)
Call Trace:
__skb_datagram_iter+0x123/0x8b0 (net/core/datagram.c:402)
skb_copy_datagram_iter+0x77/0x1a0 (net/core/datagram.c:534)
tipc_recvmsg+0x3d7/0xe80 (net/tipc/socket.c:1934)
io_recvmsg+0x47e/0xda0
Fix by changing min_t(int, ...) to min_t(size_t, ...) in both
functions. The result is always <= (dlen - offset), which is bounded
by TIPC maximum message size (0x1ffff bytes), so the implicit
narrowing on assignment to int copy is always safe. |
| In the Linux kernel, the following vulnerability has been resolved:
pds_core: fix deadlock between reset thread and remove
pci_reset_function() acquires device_lock before performing the reset.
pdsc_remove() is called by the PCI core with device_lock already held.
If pdsc_pci_reset_thread() is running when pdsc_remove() is called,
destroy_workqueue() will block waiting for the work to complete, while
the work is blocked waiting for device_lock - deadlock.
Use pci_try_reset_function() which uses pci_dev_trylock() internally.
This acquires both the device lock and the PCI config access lock
without blocking - if either lock is contended, it returns -EAGAIN
immediately. This avoids the deadlock while also ensuring proper
config space access serialization during the reset.
The pci_dev_get/put calls are also removed as they were unnecessary -
the driver-owned workqueue is destroyed in pdsc_remove(), guaranteeing
the work completes before remove returns. The PCI core holds its
reference to pci_dev throughout the entire unbind sequence. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: mt76: mt7996: fix possible NULL-pointer deref in mt7996_mcu_sta_bfer_eht()
mt76_connac_get_eht_phy_cap routine can theoretically return NULL so
check cap pointer before dereferencing it. |
