| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
net: vlan: fix VLAN 0 refcount imbalance of toggling filtering during runtime
Assuming the "rx-vlan-filter" feature is enabled on a net device, the
8021q module will automatically add or remove VLAN 0 when the net device
is put administratively up or down, respectively. There are a couple of
problems with the above scheme.
The first problem is a memory leak that can happen if the "rx-vlan-filter"
feature is disabled while the device is running:
# ip link add bond1 up type bond mode 0
# ethtool -K bond1 rx-vlan-filter off
# ip link del dev bond1
When the device is put administratively down the "rx-vlan-filter"
feature is disabled, so the 8021q module will not remove VLAN 0 and the
memory will be leaked [1].
Another problem that can happen is that the kernel can automatically
delete VLAN 0 when the device is put administratively down despite not
adding it when the device was put administratively up since during that
time the "rx-vlan-filter" feature was disabled. null-ptr-unref or
bug_on[2] will be triggered by unregister_vlan_dev() for refcount
imbalance if toggling filtering during runtime:
$ ip link add bond0 type bond mode 0
$ ip link add link bond0 name vlan0 type vlan id 0 protocol 802.1q
$ ethtool -K bond0 rx-vlan-filter off
$ ifconfig bond0 up
$ ethtool -K bond0 rx-vlan-filter on
$ ifconfig bond0 down
$ ip link del vlan0
Root cause is as below:
step1: add vlan0 for real_dev, such as bond, team.
register_vlan_dev
vlan_vid_add(real_dev,htons(ETH_P_8021Q),0) //refcnt=1
step2: disable vlan filter feature and enable real_dev
step3: change filter from 0 to 1
vlan_device_event
vlan_filter_push_vids
ndo_vlan_rx_add_vid //No refcnt added to real_dev vlan0
step4: real_dev down
vlan_device_event
vlan_vid_del(dev, htons(ETH_P_8021Q), 0); //refcnt=0
vlan_info_rcu_free //free vlan0
step5: delete vlan0
unregister_vlan_dev
BUG_ON(!vlan_info); //vlan_info is null
Fix both problems by noting in the VLAN info whether VLAN 0 was
automatically added upon NETDEV_UP and based on that decide whether it
should be deleted upon NETDEV_DOWN, regardless of the state of the
"rx-vlan-filter" feature.
[1]
unreferenced object 0xffff8880068e3100 (size 256):
comm "ip", pid 384, jiffies 4296130254
hex dump (first 32 bytes):
00 20 30 0d 80 88 ff ff 00 00 00 00 00 00 00 00 . 0.............
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
backtrace (crc 81ce31fa):
__kmalloc_cache_noprof+0x2b5/0x340
vlan_vid_add+0x434/0x940
vlan_device_event.cold+0x75/0xa8
notifier_call_chain+0xca/0x150
__dev_notify_flags+0xe3/0x250
rtnl_configure_link+0x193/0x260
rtnl_newlink_create+0x383/0x8e0
__rtnl_newlink+0x22c/0xa40
rtnl_newlink+0x627/0xb00
rtnetlink_rcv_msg+0x6fb/0xb70
netlink_rcv_skb+0x11f/0x350
netlink_unicast+0x426/0x710
netlink_sendmsg+0x75a/0xc20
__sock_sendmsg+0xc1/0x150
____sys_sendmsg+0x5aa/0x7b0
___sys_sendmsg+0xfc/0x180
[2]
kernel BUG at net/8021q/vlan.c:99!
Oops: invalid opcode: 0000 [#1] SMP KASAN PTI
CPU: 0 UID: 0 PID: 382 Comm: ip Not tainted 6.16.0-rc3 #61 PREEMPT(voluntary)
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996),
BIOS rel-1.13.0-0-gf21b5a4aeb02-prebuilt.qemu.org 04/01/2014
RIP: 0010:unregister_vlan_dev (net/8021q/vlan.c:99 (discriminator 1))
RSP: 0018:ffff88810badf310 EFLAGS: 00010246
RAX: 0000000000000000 RBX: ffff88810da84000 RCX: ffffffffb47ceb9a
RDX: dffffc0000000000 RSI: 0000000000000008 RDI: ffff88810e8b43c8
RBP: 0000000000000000 R08: 0000000000000000 R09: fffffbfff6cefe80
R10: ffffffffb677f407 R11: ffff88810badf3c0 R12: ffff88810e8b4000
R13: 0000000000000000 R14: ffff88810642a5c0 R15: 000000000000017e
FS: 00007f1ff68c20c0(0000) GS:ffff888163a24000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 00007f1ff5dad240 CR3: 0000000107e56000 CR4: 00000000000006f0
Call Trace:
<TASK
---truncated--- |
| In the Linux kernel, the following vulnerability has been resolved:
perf: Revert to requiring CAP_SYS_ADMIN for uprobes
Jann reports that uprobes can be used destructively when used in the
middle of an instruction. The kernel only verifies there is a valid
instruction at the requested offset, but due to variable instruction
length cannot determine if this is an instruction as seen by the
intended execution stream.
Additionally, Mark Rutland notes that on architectures that mix data
in the text segment (like arm64), a similar things can be done if the
data word is 'mistaken' for an instruction.
As such, require CAP_SYS_ADMIN for uprobes. |
| In the Linux kernel, the following vulnerability has been resolved:
vsock: Fix transport_* TOCTOU
Transport assignment may race with module unload. Protect new_transport
from becoming a stale pointer.
This also takes care of an insecure call in vsock_use_local_transport();
add a lockdep assert.
BUG: unable to handle page fault for address: fffffbfff8056000
Oops: Oops: 0000 [#1] SMP KASAN
RIP: 0010:vsock_assign_transport+0x366/0x600
Call Trace:
vsock_connect+0x59c/0xc40
__sys_connect+0xe8/0x100
__x64_sys_connect+0x6e/0xc0
do_syscall_64+0x92/0x1c0
entry_SYSCALL_64_after_hwframe+0x4b/0x53 |
| In the Linux kernel, the following vulnerability has been resolved:
atm: clip: Fix potential null-ptr-deref in to_atmarpd().
atmarpd is protected by RTNL since commit f3a0592b37b8 ("[ATM]: clip
causes unregister hang").
However, it is not enough because to_atmarpd() is called without RTNL,
especially clip_neigh_solicit() / neigh_ops->solicit() is unsleepable.
Also, there is no RTNL dependency around atmarpd.
Let's use a private mutex and RCU to protect access to atmarpd in
to_atmarpd(). |
| In the Linux kernel, the following vulnerability has been resolved:
KVM: SVM: Reject SEV{-ES} intra host migration if vCPU creation is in-flight
Reject migration of SEV{-ES} state if either the source or destination VM
is actively creating a vCPU, i.e. if kvm_vm_ioctl_create_vcpu() is in the
section between incrementing created_vcpus and online_vcpus. The bulk of
vCPU creation runs _outside_ of kvm->lock to allow creating multiple vCPUs
in parallel, and so sev_info.es_active can get toggled from false=>true in
the destination VM after (or during) svm_vcpu_create(), resulting in an
SEV{-ES} VM effectively having a non-SEV{-ES} vCPU.
The issue manifests most visibly as a crash when trying to free a vCPU's
NULL VMSA page in an SEV-ES VM, but any number of things can go wrong.
BUG: unable to handle page fault for address: ffffebde00000000
#PF: supervisor read access in kernel mode
#PF: error_code(0x0000) - not-present page
PGD 0 P4D 0
Oops: Oops: 0000 [#1] SMP KASAN NOPTI
CPU: 227 UID: 0 PID: 64063 Comm: syz.5.60023 Tainted: G U O 6.15.0-smp-DEV #2 NONE
Tainted: [U]=USER, [O]=OOT_MODULE
Hardware name: Google, Inc. Arcadia_IT_80/Arcadia_IT_80, BIOS 12.52.0-0 10/28/2024
RIP: 0010:constant_test_bit arch/x86/include/asm/bitops.h:206 [inline]
RIP: 0010:arch_test_bit arch/x86/include/asm/bitops.h:238 [inline]
RIP: 0010:_test_bit include/asm-generic/bitops/instrumented-non-atomic.h:142 [inline]
RIP: 0010:PageHead include/linux/page-flags.h:866 [inline]
RIP: 0010:___free_pages+0x3e/0x120 mm/page_alloc.c:5067
Code: <49> f7 06 40 00 00 00 75 05 45 31 ff eb 0c 66 90 4c 89 f0 4c 39 f0
RSP: 0018:ffff8984551978d0 EFLAGS: 00010246
RAX: 0000777f80000001 RBX: 0000000000000000 RCX: ffffffff918aeb98
RDX: 0000000000000000 RSI: 0000000000000008 RDI: ffffebde00000000
RBP: 0000000000000000 R08: ffffebde00000007 R09: 1ffffd7bc0000000
R10: dffffc0000000000 R11: fffff97bc0000001 R12: dffffc0000000000
R13: ffff8983e19751a8 R14: ffffebde00000000 R15: 1ffffd7bc0000000
FS: 0000000000000000(0000) GS:ffff89ee661d3000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: ffffebde00000000 CR3: 000000793ceaa000 CR4: 0000000000350ef0
DR0: 0000000000000000 DR1: 0000000000000b5f DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000ffff0ff0 DR7: 0000000000000400
Call Trace:
<TASK>
sev_free_vcpu+0x413/0x630 arch/x86/kvm/svm/sev.c:3169
svm_vcpu_free+0x13a/0x2a0 arch/x86/kvm/svm/svm.c:1515
kvm_arch_vcpu_destroy+0x6a/0x1d0 arch/x86/kvm/x86.c:12396
kvm_vcpu_destroy virt/kvm/kvm_main.c:470 [inline]
kvm_destroy_vcpus+0xd1/0x300 virt/kvm/kvm_main.c:490
kvm_arch_destroy_vm+0x636/0x820 arch/x86/kvm/x86.c:12895
kvm_put_kvm+0xb8e/0xfb0 virt/kvm/kvm_main.c:1310
kvm_vm_release+0x48/0x60 virt/kvm/kvm_main.c:1369
__fput+0x3e4/0x9e0 fs/file_table.c:465
task_work_run+0x1a9/0x220 kernel/task_work.c:227
exit_task_work include/linux/task_work.h:40 [inline]
do_exit+0x7f0/0x25b0 kernel/exit.c:953
do_group_exit+0x203/0x2d0 kernel/exit.c:1102
get_signal+0x1357/0x1480 kernel/signal.c:3034
arch_do_signal_or_restart+0x40/0x690 arch/x86/kernel/signal.c:337
exit_to_user_mode_loop kernel/entry/common.c:111 [inline]
exit_to_user_mode_prepare include/linux/entry-common.h:329 [inline]
__syscall_exit_to_user_mode_work kernel/entry/common.c:207 [inline]
syscall_exit_to_user_mode+0x67/0xb0 kernel/entry/common.c:218
do_syscall_64+0x7c/0x150 arch/x86/entry/syscall_64.c:100
entry_SYSCALL_64_after_hwframe+0x76/0x7e
RIP: 0033:0x7f87a898e969
</TASK>
Modules linked in: gq(O)
gsmi: Log Shutdown Reason 0x03
CR2: ffffebde00000000
---[ end trace 0000000000000000 ]---
Deliberately don't check for a NULL VMSA when freeing the vCPU, as crashing
the host is likely desirable due to the VMSA being consumed by hardware.
E.g. if KVM manages to allow VMRUN on the vCPU, hardware may read/write a
bogus VMSA page. Accessing P
---truncated--- |
| In the Linux kernel, the following vulnerability has been resolved:
bnxt_en: Set DMA unmap len correctly for XDP_REDIRECT
When transmitting an XDP_REDIRECT packet, call dma_unmap_len_set()
with the proper length instead of 0. This bug triggers this warning
on a system with IOMMU enabled:
WARNING: CPU: 36 PID: 0 at drivers/iommu/dma-iommu.c:842 __iommu_dma_unmap+0x159/0x170
RIP: 0010:__iommu_dma_unmap+0x159/0x170
Code: a8 00 00 00 00 48 c7 45 b0 00 00 00 00 48 c7 45 c8 00 00 00 00 48 c7 45 a0 ff ff ff ff 4c 89 45
b8 4c 89 45 c0 e9 77 ff ff ff <0f> 0b e9 60 ff ff ff e8 8b bf 6a 00 66 66 2e 0f 1f 84 00 00 00 00
RSP: 0018:ff22d31181150c88 EFLAGS: 00010206
RAX: 0000000000002000 RBX: 00000000e13a0000 RCX: 0000000000000000
RDX: 0000000000000000 RSI: 0000000000000000 RDI: 0000000000000000
RBP: ff22d31181150cf0 R08: ff22d31181150ca8 R09: 0000000000000000
R10: 0000000000000000 R11: ff22d311d36c9d80 R12: 0000000000001000
R13: ff13544d10645010 R14: ff22d31181150c90 R15: ff13544d0b2bac00
FS: 0000000000000000(0000) GS:ff13550908a00000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 00005be909dacff8 CR3: 0008000173408003 CR4: 0000000000f71ef0
PKRU: 55555554
Call Trace:
<IRQ>
? show_regs+0x6d/0x80
? __warn+0x89/0x160
? __iommu_dma_unmap+0x159/0x170
? report_bug+0x17e/0x1b0
? handle_bug+0x46/0x90
? exc_invalid_op+0x18/0x80
? asm_exc_invalid_op+0x1b/0x20
? __iommu_dma_unmap+0x159/0x170
? __iommu_dma_unmap+0xb3/0x170
iommu_dma_unmap_page+0x4f/0x100
dma_unmap_page_attrs+0x52/0x220
? srso_alias_return_thunk+0x5/0xfbef5
? xdp_return_frame+0x2e/0xd0
bnxt_tx_int_xdp+0xdf/0x440 [bnxt_en]
__bnxt_poll_work_done+0x81/0x1e0 [bnxt_en]
bnxt_poll+0xd3/0x1e0 [bnxt_en] |
| In the Linux kernel, the following vulnerability has been resolved:
ksmbd: fix potential use-after-free in oplock/lease break ack
If ksmbd_iov_pin_rsp return error, use-after-free can happen by
accessing opinfo->state and opinfo_put and ksmbd_fd_put could
called twice. |
| In the Linux kernel, the following vulnerability has been resolved:
nfsd: nfsd4_spo_must_allow() must check this is a v4 compound request
If the request being processed is not a v4 compound request, then
examining the cstate can have undefined results.
This patch adds a check that the rpc procedure being executed
(rq_procinfo) is the NFSPROC4_COMPOUND procedure. |
| In the Linux kernel, the following vulnerability has been resolved:
perf: Fix sample vs do_exit()
Baisheng Gao reported an ARM64 crash, which Mark decoded as being a
synchronous external abort -- most likely due to trying to access
MMIO in bad ways.
The crash further shows perf trying to do a user stack sample while in
exit_mmap()'s tlb_finish_mmu() -- i.e. while tearing down the address
space it is trying to access.
It turns out that we stop perf after we tear down the userspace mm; a
receipie for disaster, since perf likes to access userspace for
various reasons.
Flip this order by moving up where we stop perf in do_exit().
Additionally, harden PERF_SAMPLE_CALLCHAIN and PERF_SAMPLE_STACK_USER
to abort when the current task does not have an mm (exit_mm() makes
sure to set current->mm = NULL; before commencing with the actual
teardown). Such that CPU wide events don't trip on this same problem. |
| In the Linux kernel, the following vulnerability has been resolved:
platform/x86: dell-wmi-sysman: Fix WMI data block retrieval in sysfs callbacks
After retrieving WMI data blocks in sysfs callbacks, check for the
validity of them before dereferencing their content. |
| In the Linux kernel, the following vulnerability has been resolved:
scsi: target: Fix NULL pointer dereference in core_scsi3_decode_spec_i_port()
The function core_scsi3_decode_spec_i_port(), in its error code path,
unconditionally calls core_scsi3_lunacl_undepend_item() passing the
dest_se_deve pointer, which may be NULL.
This can lead to a NULL pointer dereference if dest_se_deve remains
unset.
SPC-3 PR SPEC_I_PT: Unable to locate dest_tpg
Unable to handle kernel paging request at virtual address dfff800000000012
Call trace:
core_scsi3_lunacl_undepend_item+0x2c/0xf0 [target_core_mod] (P)
core_scsi3_decode_spec_i_port+0x120c/0x1c30 [target_core_mod]
core_scsi3_emulate_pro_register+0x6b8/0xcd8 [target_core_mod]
target_scsi3_emulate_pr_out+0x56c/0x840 [target_core_mod]
Fix this by adding a NULL check before calling
core_scsi3_lunacl_undepend_item() |
| In the Linux kernel, the following vulnerability has been resolved:
regulator: gpio: Fix the out-of-bounds access to drvdata::gpiods
drvdata::gpiods is supposed to hold an array of 'gpio_desc' pointers. But
the memory is allocated for only one pointer. This will lead to
out-of-bounds access later in the code if 'config::ngpios' is > 1. So
fix the code to allocate enough memory to hold 'config::ngpios' of GPIO
descriptors.
While at it, also move the check for memory allocation failure to be below
the allocation to make it more readable. |
| In the Linux kernel, the following vulnerability has been resolved:
NFSv4/pNFS: Fix a race to wake on NFS_LAYOUT_DRAIN
We found a few different systems hung up in writeback waiting on the same
page lock, and one task waiting on the NFS_LAYOUT_DRAIN bit in
pnfs_update_layout(), however the pnfs_layout_hdr's plh_outstanding count
was zero.
It seems most likely that this is another race between the waiter and waker
similar to commit ed0172af5d6f ("SUNRPC: Fix a race to wake a sync task").
Fix it up by applying the advised barrier. |
| In the Linux kernel, the following vulnerability has been resolved:
ACPICA: Refuse to evaluate a method if arguments are missing
As reported in [1], a platform firmware update that increased the number
of method parameters and forgot to update a least one of its callers,
caused ACPICA to crash due to use-after-free.
Since this a result of a clear AML issue that arguably cannot be fixed
up by the interpreter (it cannot produce missing data out of thin air),
address it by making ACPICA refuse to evaluate a method if the caller
attempts to pass fewer arguments than expected to it. |
| In the Linux kernel, the following vulnerability has been resolved:
btrfs: fix iteration of extrefs during log replay
At __inode_add_ref() when processing extrefs, if we jump into the next
label we have an undefined value of victim_name.len, since we haven't
initialized it before we did the goto. This results in an invalid memory
access in the next iteration of the loop since victim_name.len was not
initialized to the length of the name of the current extref.
Fix this by initializing victim_name.len with the current extref's name
length. |
| In the Linux kernel, the following vulnerability has been resolved:
rose: fix dangling neighbour pointers in rose_rt_device_down()
There are two bugs in rose_rt_device_down() that can cause
use-after-free:
1. The loop bound `t->count` is modified within the loop, which can
cause the loop to terminate early and miss some entries.
2. When removing an entry from the neighbour array, the subsequent entries
are moved up to fill the gap, but the loop index `i` is still
incremented, causing the next entry to be skipped.
For example, if a node has three neighbours (A, A, B) with count=3 and A
is being removed, the second A is not checked.
i=0: (A, A, B) -> (A, B) with count=2
^ checked
i=1: (A, B) -> (A, B) with count=2
^ checked (B, not A!)
i=2: (doesn't occur because i < count is false)
This leaves the second A in the array with count=2, but the rose_neigh
structure has been freed. Code that accesses these entries assumes that
the first `count` entries are valid pointers, causing a use-after-free
when it accesses the dangling pointer.
Fix both issues by iterating over the array in reverse order with a fixed
loop bound. This ensures that all entries are examined and that the removal
of an entry doesn't affect subsequent iterations. |
| In the Linux kernel, the following vulnerability has been resolved:
virtio-net: ensure the received length does not exceed allocated size
In xdp_linearize_page, when reading the following buffers from the ring,
we forget to check the received length with the true allocate size. This
can lead to an out-of-bound read. This commit adds that missing check. |
| In the Linux kernel, the following vulnerability has been resolved:
btrfs: fix a race between renames and directory logging
We have a race between a rename and directory inode logging that if it
happens and we crash/power fail before the rename completes, the next time
the filesystem is mounted, the log replay code will end up deleting the
file that was being renamed.
This is best explained following a step by step analysis of an interleaving
of steps that lead into this situation.
Consider the initial conditions:
1) We are at transaction N;
2) We have directories A and B created in a past transaction (< N);
3) We have inode X corresponding to a file that has 2 hardlinks, one in
directory A and the other in directory B, so we'll name them as
"A/foo_link1" and "B/foo_link2". Both hard links were persisted in a
past transaction (< N);
4) We have inode Y corresponding to a file that as a single hard link and
is located in directory A, we'll name it as "A/bar". This file was also
persisted in a past transaction (< N).
The steps leading to a file loss are the following and for all of them we
are under transaction N:
1) Link "A/foo_link1" is removed, so inode's X last_unlink_trans field
is updated to N, through btrfs_unlink() -> btrfs_record_unlink_dir();
2) Task A starts a rename for inode Y, with the goal of renaming from
"A/bar" to "A/baz", so we enter btrfs_rename();
3) Task A inserts the new BTRFS_INODE_REF_KEY for inode Y by calling
btrfs_insert_inode_ref();
4) Because the rename happens in the same directory, we don't set the
last_unlink_trans field of directoty A's inode to the current
transaction id, that is, we don't cal btrfs_record_unlink_dir();
5) Task A then removes the entries from directory A (BTRFS_DIR_ITEM_KEY
and BTRFS_DIR_INDEX_KEY items) when calling __btrfs_unlink_inode()
(actually the dir index item is added as a delayed item, but the
effect is the same);
6) Now before task A adds the new entry "A/baz" to directory A by
calling btrfs_add_link(), another task, task B is logging inode X;
7) Task B starts a fsync of inode X and after logging inode X, at
btrfs_log_inode_parent() it calls btrfs_log_all_parents(), since
inode X has a last_unlink_trans value of N, set at in step 1;
8) At btrfs_log_all_parents() we search for all parent directories of
inode X using the commit root, so we find directories A and B and log
them. Bu when logging direct A, we don't have a dir index item for
inode Y anymore, neither the old name "A/bar" nor for the new name
"A/baz" since the rename has deleted the old name but has not yet
inserted the new name - task A hasn't called yet btrfs_add_link() to
do that.
Note that logging directory A doesn't fallback to a transaction
commit because its last_unlink_trans has a lower value than the
current transaction's id (see step 4);
9) Task B finishes logging directories A and B and gets back to
btrfs_sync_file() where it calls btrfs_sync_log() to persist the log
tree;
10) Task B successfully persisted the log tree, btrfs_sync_log() completed
with success, and a power failure happened.
We have a log tree without any directory entry for inode Y, so the
log replay code deletes the entry for inode Y, name "A/bar", from the
subvolume tree since it doesn't exist in the log tree and the log
tree is authorative for its index (we logged a BTRFS_DIR_LOG_INDEX_KEY
item that covers the index range for the dentry that corresponds to
"A/bar").
Since there's no other hard link for inode Y and the log replay code
deletes the name "A/bar", the file is lost.
The issue wouldn't happen if task B synced the log only after task A
called btrfs_log_new_name(), which would update the log with the new name
for inode Y ("A/bar").
Fix this by pinning the log root during renames before removing the old
directory entry, and unpinning af
---truncated--- |
| In the Linux kernel, the following vulnerability has been resolved:
posix-cpu-timers: fix race between handle_posix_cpu_timers() and posix_cpu_timer_del()
If an exiting non-autoreaping task has already passed exit_notify() and
calls handle_posix_cpu_timers() from IRQ, it can be reaped by its parent
or debugger right after unlock_task_sighand().
If a concurrent posix_cpu_timer_del() runs at that moment, it won't be
able to detect timer->it.cpu.firing != 0: cpu_timer_task_rcu() and/or
lock_task_sighand() will fail.
Add the tsk->exit_state check into run_posix_cpu_timers() to fix this.
This fix is not needed if CONFIG_POSIX_CPU_TIMERS_TASK_WORK=y, because
exit_task_work() is called before exit_notify(). But the check still
makes sense, task_work_add(&tsk->posix_cputimers_work.work) will fail
anyway in this case. |
| In the Linux kernel, the following vulnerability has been resolved:
software node: Correct a OOB check in software_node_get_reference_args()
software_node_get_reference_args() wants to get @index-th element, so
the property value requires at least '(index + 1) * sizeof(*ref)' bytes
but that can not be guaranteed by current OOB check, and may cause OOB
for malformed property.
Fix by using as OOB check '((index + 1) * sizeof(*ref) > prop->length)'. |
